Draft Beer Equipment

Home / Homebrewing / Draft Beer Equipment
Faucet Lever Stainless Steel
The Stainless Steel Lever fits into the top opening of a standard Chrome Faucet body and opens and closes the faucet during dispensing. Manufactured with inert stainless steel, the Faucet Lever provides a sanitary contact point in faucets installed into
Add to cart
Faucet Lever Stainless Steel
$6.25
Clamp Crimper
Provides proper crimping of Oetiker clamps to beverage and gas tubing, creating liquid or gas tight seals.Oetiker clamps are often utilized for permanent installations.Crimper attaches clamps to and removes clamps from tubing in beverage installations.
Add to cart
Clamp Crimper
$10.99
Tubing BEVLEX #200 Beverage 1/4" ID - CLEAR 100 ft Roll
Bevlex® Series 200
Special dual durometer construction combines a low extraction inner contact surface with a flexible outer layer for excellent kink resistance and taste protection properties.
Tubing BEVLEX #200 Beverage 1/4" ID - CLEAR 100 ft Roll
$88.00
Universal Poppet Valve
Universal Replacement Poppet Valve
Add to cart
Universal Poppet Valve
$2.99
Tubing Silicone High Temp 1/2'' ID - Per Foot
High Temp tubing is ideal for the transfer of hot water and wort during brewing processes, especially from boiling vessel to wort chiller.
Add to cart
Tubing Silicone High Temp 1/2'' ID - Per Foot
$6.49
Single Shank 4" Stainless Steel
The 4" Stainless Steel Shank fits 1” to 2 ½” thick walls and ships complete with black finishing flange, faucet coupling nut and interior securing nut. Shanks provide the crucial connection point between faucets and the serving keg.Appl
Add to cart
Single Shank 4" Stainless Steel
$19.99
Rubber Gauge Boot
The economical Rubber Gauge boot easily slips over regulator gauges, offering protection against accidental impact and damage.
Add to cart
Rubber Gauge Boot
$4.25
O-Ring Closure Original / Keg
Formed of high quality soft rubber, the Closure Original fits both ball and pin lock keg lids, providing effective leak protection for beers requiring low and high – pressure CO2 settings.To prevent troublesome leaks and potential infections, Brew a
O-Ring Closure Original / Keg
$3.99
CarbaCap
For swift carbonation of still beverages such as beer, soda, cider, juice, wine, energy drinks…, the CarbaCap permits the infusion of CO2 with minimal effort.
CarbaCap
$21.00
Tailpiece Stainless Steel 3/8'' Barb (Fits 5/16" Tubing)
Stainless Steel Tail Piece
Add to cart
Tailpiece Stainless Steel 3/8'' Barb (Fits 5/16" Tubing)
$6.49
Faucet Wrench Standard
A Faucet Wrench is a needed tool for installing and removing faucets from shanks attached to Tap Towers, Keggerators or Jockey Box systems, proving invaluable in tightening the faucet to the shank and preventing leaks.
Add to cart
Faucet Wrench Standard
$8.99
Portable CO2 Charger Cornelius Keg
Portable CO2 Charger Cornelius Keg
Add to cart
Portable CO2 Charger Cornelius Keg
$27.99
Poppet Valve (Becker)
Periodically, during serving or carbonating operations, the Becker Disconnect Poppet may become damaged or wear out over time, leaking CO2 or liquid from the keg.  To replace the poppet, simply unscrew the Liquid Plug Cap from the top of the disconne
Poppet Valve (Becker)
$3.99
Disconnect Pin Liquid
Manufactured with three locking slots to match the beverage out pins of the tank plug on a pin lock soda keg, the Liquid Pin Disconnect requires a beverage, nut and stem assembly for proper connection to ¼” or 3/16” beverage tubing.
Add to cart
Disconnect Pin Liquid
$10.20
Disconnect Pin Gas
Manufactured with two locking slots to match the gas in pins of a tank plug on a pin lock soda keg, the Gas Pin Disconnect requires a gas, nut and stem assembly for proper connection to 5/16” gas tubing.
Add to cart
Disconnect Pin Gas
$10.20
Dip Tube Liquid - 5 Gal Ball Lock Keg
Constructed of stainless steel, the Beverage Dip Tube is manufactured with a curve near the mid-point of the tube, conforming to Ball Lock Keg design. To complete installation, the Beverage Dip Tube requires a Dip Tube O-Ring to prevent foaming and facili
Add to cart
Dip Tube Liquid - 5 Gal Ball Lock Keg
$13.99
CO2 Keg Charger Refill - 16g
CO2 Keg Charger Refill - 16 Gram
Add to cart
CO2 Keg Charger Refill - 16g
$2.38
O-Ring Ball Lock Plug (Black)
Replacement o-ring fits the groove at the top of both gas and beverage plugs attached to ball lock kegs.Brew and Grow recommends replacing o-rings when leaks occur with ball or pin lock disconnects attached to either gas or beverage plugs. Gas or Bev
Add to cart
O-Ring Ball Lock Plug (Black)
$0.99
Clamp Stepless 3/8" - Gas Hose
Oetiker clamps are typically utilized in permanent installations, attaching 5/16” gas tubing to Gas Disconnect stems and the outlet barbs of regulators connected to CO2 tanks.Clamp requires Clamp Crimper for appropriate installation.
Add to cart
Clamp Stepless 3/8" - Gas Hose
$0.70
Chrome-Plated Coupling Nut
The Coupling Nut secures the connection between the Phaucet Adaptor and the threads machined into the body of a Chrome or Perlick Faucet. To complete the assembly, a Faucet Wrench is required to fasten the components together and create a liquid tight sea
Add to cart
Chrome-Plated Coupling Nut
$4.75
Nut & Stem 3/8" - Gas
The Gas Nut and Stem Assembly is the connection interface between Gas Disconnects and 5/16” Gas Tubing. To secure gas tubing to the Gas Nut and Stem assembly use one of the following clamps: Large Worm Clamp, Gas Stepless 3/8” or a Gas Kw
Add to cart
Nut & Stem 3/8" - Gas
$5.99
Ball Lock Conversion for Sanke Coupler - Liquid
Attach a pair of ball-lock disconnects to your existing beer lines and install these plugs onto your keg coupler. Now you can easily switch between product tanks and kegs.
Add to cart
Ball Lock Conversion for Sanke Coupler - Liquid
$15.49
Column Shank w/ 1/4" Barbed Elbow (304 SS)
304 Grade Stainless Steel Column Shanks
Column Shank w/ 1/4" Barbed Elbow (304 SS)
$22.99
Adapter CO-2-Go
Allows you to attach a CO2 regulator to a CO2 paintball cylinder.
Add to cart
Adapter CO-2-Go
$16.99