Draft Beer Equipment

Manufactured with two locking slots to match the gas in pins of a tank plug on a pin lock soda keg, the Gas Pin Disconnect requires a gas, nut and stem assembly for proper connection to 5/16” gas tubing.

The Pin Lock Socket is the proper tool for removing gas or liquid tank plugs from pin lock kegs. Manufactured with four strategically placed notches for latching onto 2 pin or 3 pin tank plugs, the socket fits standard 1/2” socket drivers and remove

Pin Lock kegs were designed with automatic pressure relief valves embedded in the keg lids and cannot be manually depressurized through the valve on the lid.The Plastic Depressurizer easily attaches to the tank plug with 2 – pins. Once placed on the

The Oxygen Regulator fits most disposable O2 tanks, including tanks sold at hardware stores. Regulator is reverse thread.

Formed of high quality soft rubber, the Closure Original fits both ball and pin lock keg lids, providing effective leak protection for beers requiring low and high – pressure CO2 settings.To prevent troublesome leaks and potential infections, Brew a

Provides proper crimping of Oetiker clamps to beverage and gas tubing, creating liquid or gas tight seals.Oetiker clamps are often utilized for permanent installations.Crimper attaches clamps to and removes clamps from tubing in beverage installations.

Pour Stout with the creamy texture and the classic cascade of a Dublin pub! The Chrome Stout Faucet is manufactured with a restrictor plate, providing the correct turbulence to create the rich, velvety mouthfeel expected of stout.To complete the system, c

The Gas Nut and Stem Assembly is the connection interface between Gas Disconnects and 5/16” Gas Tubing. To secure gas tubing to the Gas Nut and Stem assembly use one of the following clamps: Large Worm Clamp, Gas Stepless 3/8” or a Gas Kw

Attach a pair of ball-lock disconnects to your existing beer lines and install these plugs onto your keg coupler. Now you can easily switch between product tanks and kegs.

Universal Replacement Poppet Valve

Flare Adapter 1/4 MFL X 1/4 MFL

O-Ring Perlick Replacement

Allows you to attach a CO2 regulator to a CO2 paintball cylinder.

Neoprene Washer’s provide liquid or gas tight seals at the assembly points between barbs and shanks or barbs and gas inlets and beverage outlets of Sanke Tapping devices for commercial kegs.

The In-Line ¼” Hose Barb with shutoff x Female allows for quick and easy disconnection and connection of gas line in draft systems.

Worm Clamps are typically utilized in temporary or permanent installations in beverage and brewing systems. Attached or removed with a standard flat head screwdriver, the 1/8” – ½” worm clamp fastens 3/16” or ¼” tubing

Worm Clamps are typically utilized in temporary or permanent installations in beverage and brewing systems. Attached or removed with a standard flat head screwdriver, the ¼” – 7/8” worm clamp fastens 5/16”gas tubing to stems o

In draft systems, Hex Nuts fasten tail pieces to faucet shanks and tail pieces to the gas inlet and beverage outlets of Sanke Tap Couplers. Wing Nuts can be hand tightened to properly form a liquid or gas tight seal.

Plug fits John Wood Model 85 Ball Lock Kegs and Firestone Challenger kegs. Assembly includes poppet, plastic insert and o-ring.Application Tip:Solving troublesome leaks may require measures beyond replacing a poppet or an o-ring. Occasionally, plugs

In draft systems, Tail Pieces are the connection interface between shanks and beverage tubing and between commercial Sanke Keg Couplers and beverage and gas tubing. Ideal for matching to 3/16” ID beverage tubing, the 3/16” Tail Piece requires

3 – Way Air Distributors provide home brewers with the capability of serving beer from three kegs while utilizing a single CO2 tank. Outlet barbs fit standard 5/16” gas tubing. Shut-off valves are equipped with ball check valves and each spli